Description
Additional photos are available here for your perusal.
In 1992, Honda raised the bar in the sport bike sector when it debuted the lightweight and powerful CBR900RR. Designed by Tadao Baba, the 900 was designed to offer the power of an open-class superbike in a svelte 600-sized package. The 893cc in-line four made 124hp, 65 ft-lbs of torque, and offered a top-speed of 160mph, all while tipping the scales at around 450 lbs wet. The RR set a new benchmark in the industry, and Honda enjoyed its years on top with the 900. But everything changed in 1998 when Yamaha released the first R1.
Honda fought back with an all-new model, the CBR929RR. The only pieces that were interchangeable from the outgoing model were the countershaft sprocket and clutch plates – everything else was completely novel. At the heart of the 929 was an all-new over square engine that made some major advancements over the first Fireblade. Thanks to a cleverly-designed high-flowing cylinder head and a bevy of trick lightweight internals, the 929 produced significantly more power than the 900 at higher RPM. The 929 also featured Honda’s PGM-FI (Programmable digital electronic fuel injection) and 40mm Keihin throttle bodies — with one injector per cylinder — developed with Honda specifically for the 929.
The package also included the firm’s HTEV (Honda Titanium Exhaust Valves), as well as a flapper valve in the airbox to bolster mid-range power. The liquid-cooled, four-stroke, DOHC, 929cc, four-cylinder engine put down 152 hp at 10,750 rpm and 76.1 ft-lbs of torque at 9,000 rpm — a major jump over the first double-R. Admittedly, the Honda was a little down on power compared to the Yamaha, however, the RR more than made up for it in the corners. While the original 900RR featured a front-end designed to look like an inverted unit, the 929 was equipped with an actual pair of upside-down forks; a 43mm HMAS (Honda Multi-Action System) set that was fully adjustable, just like the piggyback-reservoir-equipped monoshock. Stopping power came from dual 330mm discs pinched by four-pot Nissin calipers, and as Cycle World put it, they “refuse to fade”. Another major change on the 929 was its 17-inch front-wheel.
This example is VIN: JH2SC44A6YM014796. It came to Iconic as an import; prior history is not known.
The odometer shows 57,769 kilometers (35,895 miles).
Maintenance:
In preparation for the listing, the seller had us replace the battery, change the oil and oil filter, service the chain, clean and regrease the right switch assembly, order a spare key, and give the bike a detail.
Steve did the work, he notes the following in his condition report:
Fuel Tank Internal: Oxidation present
Tire Years – Front/ Rear: 2014
Tire Life – Front: 60%; Rear: 40%
Tire Pressure – Front: 36PSI; Rear: 42PSI
Brake Life – Front: 90%; Rear: 60%
Hydraulic Fluid – Front/Rear: Fresh
Engine Oil – Level: Ok; Quality: New
Coolant: Level: Ok; Quality: Ok
Low Beam: Ok
High Beam: Ok
Passing Light: Ok
Turn Signals: Ok
Tail Light: Ok
Brake Light: Ok
Plate Light: Ok
Killswitch: Ok
Horn: Ok
Battery: 12.68V; Charging: 14.23V; New Battery
BIKE CONDITION
– Fender eliminator installed
– Upgraded Brembo calipers
– Aftermarket fuel cap cover/sticker
REPAIRS RECOMMENDED
– Spare key, current key bends easily and may break
– Front and rear tires
– Fuel tank cleaning/lining
Modifications:
Upgraded Brembo calipers, braided stainless steel brake lines.
Aftermarket levers, Domino grips, aftermarket bar-ends.
It is riding on Dunlop Sportmax Alpha 13 tires with date codes of 1514 and 1614.
Cosmetic Blemishes: please see the album up top for all known cosmetic blemishes. Here is a selection:
Currently located at our facility in Santa Monica, California (please make an appointment for an inspection), this Honda is offered on a clean Oregon title. Please note that as an import, this bike lacks certain compliance and emissions stickers that the state of California would require to transfer a title. Have any CBR929RR stories or questions about this listing? Let us know in the “Comments” tab!